Range Check - Carbon Fuses

All new fuses from Samba is made of full carbon / kevlar. carbon / kevlar fuses are much stronger and lighter than conventional glass fuses. If anyone wants glass fuses it is no problem just specify it in your order to your local dealer.

Some precautions needs to be made when using carbon fuses because carbon leads electrical currents and also bounces our transmitter signal in a bad way. The most important is that we do not want our antennas to be parallel / near the on the outside of the fuse. Make some solution to get the antenna away from the fuse and you have found your solution.
Here is some solutions used by the worlds best pilots.

Range Check:
How range check is done is different to each brand of Radio used.
Normally the range without any disturbance should be at least 50-100m with the transmitter antenna 20cm long and the airplane in 1m height over ground. If this is not achieved then DO NOT FLY YOUR MODEL.

Receiver type:
Always use a good receiver mainly of Dual Conversion / Dobbel Super -type.
Always use crystal from the same company as the Rx
Good and proven receiver is (many others is also good):
- Graupner SMC receivers
- Multiplex IPD DS receivers
- Shulze 835

Antenna length:
Antenna length is important for our receivers. 
Common knowledge have been that it needs to be exactly as delivered by manufacturer. This is in many ways wrong. Best antenna length at 35mHz is around 9m long. Since this is impossible in a model airplane the receiver is electronically changed so that shorter antennas can be used. Normally the antenna of a typical receiver on 35mHz is 80-90cm long and a bit shorter for 40mHz. 
Lengthening the antenna by 30-100cm is no problem and only increases reception quality.
There are a few length that one should avoid because of the wavelength we are using. 100-110cm and 200-220cm antenna length is not good length. Other length is no problem.
Since most of our antenna length is inside the carbon housing of the fuse we always lengthen the antenna that is outside the fuse.

Your model:
There are many ways of getting good reception and it is always different solutions in different models.
Try the different solutions or find your own solution. This page does not describe the only way to do it.

Solution 1:
Take out the antenna just behind the wing and lengthen it so that 80-90cm is outside of fuse. Tape the first 10-30cm to the fuse so that it is not in the way while throwing the model. You can tape the antenna further back but have at least 20-30cm of it hanging straight down.
Do always take the antenna out BEHIND the wing as this as proven to be better than by the nosecone.

Solution 2 - Inside V-tail:
This solution involves some more soldering and work but it looks nice and makes the antenna disappear.
Lengthen the antenna and take it all the way inside the fuse. Glue two 20-30cm long wires inside the hinge line of your V-tail. Solder the two ends to the end of the antenna coming out of the fuse.
You have now one antenna that works like a Y-antenna and is good in any angle of the fuse to the ground.
If better reception is needed you can solder a 10-20cm long wire to the solder point at the back of the fuse and the antenna works like a X-antenna.

Solution 3 - Inside X-tail:
This solution is almost the same as solution 2 but here we need also 20cm of 0,5-0,8mm iron rod.
The solution also involves some more soldering and work but it looks nice and makes the antenna look cool also. Lengthen the antenna and take it all the way inside the fuse and up the hinge line of the rudder. Solder the end of the antenna to a 0,5-0,8mm iron rod that is drilled out the top of the rudder going backwards. Make a bend on the iron rod inside the rudder and glue it inside the rudder.
You have now one antenna that is away from the parallel length of the fuse and should give you good range. Be sure to make a bend / circle at the end of the iron rod so that you do not harm you eyes.

Solution 4 - Antenna outside to top of rudder:
This solution is simple and easy. It is also well proven by many pilots.
Take out the antenna just behind the wingseat and lengthen (solder) the antenna so that 80-90cm are outside the fuse. Make a wire or rubber to the top of the rudder and attach to the end of the antenna. This can also be done on a V-tail.

Solution 5 - Glass fuse:
Samba model is proud to say that your wishes is always listened to. If you want glass fuse to prevent any problems with interference just order it. Any special wishes is always welcome with our company. We might need some more time to produce your wish but we are there for you!

For Samba Model 2003 - Solutions by Jo Grini